Sweet Lolita Accessories and Art: pincushion

Here's a little tutorial on how to make a cloth strawberry. You can opt to make a flower instead by not stuffing the strawberry and using it as a 'petal'. Four to six petals sewn together make a very adorable flower. My flower has a cotton filled center so that it can be used as a pincushion. I do not suggest making a felt strawberry as felt tends to be a bit too thick. Something thin like cotton (in fact, I always make cotton strawberries) is much better.

On with the tutorial!

Step 1: Draw and cut out a circle from your fabric. Fold this in half and then cut along the crease so that you have two halves.

Step 2: Fold one of the halves in half, so that you have a quarter of a circle, with the face of the fabric on the inside. Sew along the straight edge, leaving the curved edge open.

Step 3: Turn it inside-out. The face of the fabric should be showing (mine is the same on both sides). Now run a small, relatively tight gathering stitch along the open edge, and do not tie it off as we will do this after stuffing. You will already see your strawberry taking shape!

Step 4: Stuff the strawberry with cotton. You can also use very finely cut up bits of fabric if you don't have any cotton. Just make sure it's well shredded. If you are making the flower, skip this step.

Step 5: Pull the gathering thread tight, this should seal up your strawberry. Stitch it securely so that it doesn't come open.

Optional step 6: Make some leaves to add to the bottom of your strawberry. If you are making the flower, just connect these petals (unstuffed strawberries) together and place something in the middle. I used a little stuffed ball of yellow cotton.

And you're done!

Be sure to leave comments, I'd love to see any ideas and finished projects involving this!

Thought I'd make a tutorial on how to make adorable cupcake pincushions. These are roughly 1.5 to 2 inches tall and about an inch across, or 4 inches in diameter. They are very easy, not at all time consuming, and take very little material. I made my own from scraps.
These little cupcakes make great gifts, especially passed out at Lolita meet-ups!

Step 1: Choose your material. You will need at least two; one for your cake and one for your cupcake wrapper. The one for your cake must be plush, or you will end up using a good amount of material. I am using some leftover brown velvet for my 'chocolate'. It is perfectly plush. You can probably get away with a thick cotton, but velvet, felt, or even wool would be better. Make sure it is something that can handle a whole lot of needles without being ruined. The second fabric (for the wrapper) must be something more thin, such as basic cotton, which is what I've used.
** You can also opt for a third color if you wish to make a swirly cupcake. I have used a mint-green cotton for this in my tutorial.

Step 2: Cut a strip from your cake fabric (and a matching one from your swirl fabric if you're using it) measuring 2 inches tall by roughly a foot long. The length is determined by how thick your fabric is. You can determine this by rolling the fabric (or if using a swirl, roll them together) until it measures 4 inches in diameter (about 1 inch across) at the widest. Fold these in half and sew each along the bottom of the length so that you have a tube (or tubes).

Step 3: If using a swirl, place the swirl fabric on top of the cake fabric with the cake fabric sticking out just a little so that you can tuck it over the swirl fabric and then begin rolling. Then fold (in the picture below, please ignore that my swirl fabric was not quite the height as the cake- it was made from a scrap so I had to make it a bit smaller than normal) If not using the swirl, just start rolling the fabric. You want to be careful and not have the center collapse. As you roll, slowly pull the fabric down a bit.

Step 4: If using swirl fabric, cut a bit off the swirl piece so that it is slightly overlapped by the cake. Pin and sew the end so it's snug against the cupcake. I used a bit of fabric glue to add some extra sturdiness, but you don't have to.

Step 5: Cut off any extra material on the bottom of the cupcake so that it's nice and flat.

Step 6: Measure your wrapper fabric. It should be 4 inches tall by whatever the diamater of your cupcake is plus 1/2 inch. My cupcake was about 4 inches in diameter, so I measured my wrapper at 4 x 4.5 inches. The extra 1/2 inch is going to be a 1/4 inch seam allowance for each end.

Step 7: Fold the 4 inch length in half and sew the bottom to make a tube as you did with your cake.

Step 8: Now fold the tube in half and sew the pieces together along the 1/4 inch seam allowance. You should have a small tube matching the diameter of your cupcake. Turn it inside out.

Step 9: With the sewn end at the bottom, slide the wrapper up over the bottom of the cupcake. It should be nice and snug. If it is not, tighten the tube up by sewing it a little more, so that you've made your seam allowance bigger.

Step 10: Now fold the bottom of the cupcake wrapper. It is pretty much how you fold the end of a gift-wrapped package, but I will try to demonstrate. Otherwise have a look at step 4 of this for an example. We are folding it this way because it makes the bottom pretty flat, so that the cupcake can sit upright without falling over. Once folded, pin in place and sew it really well.